Tilbud!

Spark R&D Dyno DH ATK Splitboard Hardboot Kit

Spark R&D Dyno DH ATK Splitboard Hardboot Kit

Opprinnelig pris var: kr9,129.12.Nåværende pris er: kr1,294.18.

Produktnummer: SKUfQyuXxt3OT Kategorier: Hardboots Utstyr, Reservedeler, Snowboarding, Splitbindinger, Splitboard, Splitboard, Splitboardpakker, Tilbehør, Tilbehør / Deler Stikkord: Spark R&D Merke: Spark R&D

Beskrivelse
Omtaler (0)

Varekode: SW10400

Brand: Spark R&D

	Splitboardguide
	Har du behov for veiledning? Finn all informasjonen du trenger i guiden vår.
	Les nå

Obs: Dette produktet krever Hardboots.

The Dyno DH is our acclaimed hardboot specific splitboard binding. It is designed to fit a variety of touring boots from different brands and delivers high-end performance to the growing hardboot segment of splitboarders. All parts are designed and manufactured by us from start to finish for the all-around precision that you can only get from a Spark made product.

Dyno DH Bindings are for riding only. Carry them in your pack on the way up, while using your tech toes for touring. Then slide the Dynos on your pucks and lock into place with the snap ramps for the ride down. Fits boots with 255 – 340mm sole length.

Weight:0.90 lb/ea (409g) – 1.80 lb/pr (818g)

Compatibility and Setup
Spark Flat Pucks compatible (Spark Canted Pucks recommended)

Also compatible with Spark Solid Board Flat Pucks and Canted Solid Board Pucks.

Toe Clips
The toe clip is designed to fit even low profile AT boots. The slim design saves weight while maintaining backcountry dependability.

Set Screw
The set screw has a 4mm hex drive, found on our Spark Tool.

Lightweight & Strong
Stainless steel bails and anodized aluminum toe clips. The heel end of the baseplate has been reinforced to avoid bending with heavy use.

Snap Ramps
Tesla System Snap Ramps for speedy, pinless transitions.

Spark R&D X ATK Hardboot Tech Toe
A Spark R&D and ATK Binding collaboration designed and based off of the ATK Toe Piece from the Trofeo series – «Performing on Lightness.» Built specifically for the split-hardbooter, the new Spark x ATK Tech Toes utilize ATK’s signature monolink technology with smoother entry, better retention and 20% weight savings compared to the original Spark Tech Toe (now discontinued). With an integrated hole pattern for factory splitboards there is no need for an adapter. Pair with our Hardboot Dual Height Wires, and compatible D Rex ST Pro Crampons to be ready for the skin track.

The Spark x ATK Tech Toe is intended for splitboard touring only.

Weight: 4.23 oz/ea (120g) – 8.46 oz/pair (240g)

Made in Italy

Compatibility and Setup
Spark x ATK Tech Toes are best paired with with D Rex ST Pro Cramponsand Hardboot Dual Height Wires

ATK Monolink Technology
Ergal 7075 aluminum sidearms and monolink technology. A smart layout that utilizes one pair of springs to lock your boot firmly in place.

Integrated Crampon Mounts
Built-in claw mounts allow for easy use of the D Rex ST Pro Crampons and original D Rex Crampons (now discontinued)

Adjustability
Slotted rear holes compensate for splitboard insert pattern compatability and variability.

Riveted Pins
Pins are riveted to the toe piece arms, making the loss of a pin in the backcountry nearly impossible. Heat treated for incredible wear resistance.

Center Screw
Robust stainless steel center screw for easy no tool installation.

Lock Lever
Slimmed down aluminum lock lever saves weight and handles more abuse than plastic designs.

Spark R&D Black Splitboard Canted Pucks
All the same great features of our Spark Pucks, but with 3° canting for reduced knee strain.
Near infinite adjustability for splitboards with inserts. Quick mounting with super fine foot placement, angle, and toe/heel centering adjustments.

Weight: 11.36 oz/pr (322g)

Channel-like stance adjustability for splitboards built with inserts. Believe it.
This breakthrough in design has riders beyond stoked , and has made Spark Pucks our most popular splitboard accessory.

Slide them on and snap the ramp down. Snap the ramp up and slide them off. The most functional way to attach your binding to your board in ride mode. Period. Spark R&D bindings are designed to work with all puck compatible splitboard models. When used with Arc bindings conveniently access puck screws with the bindings in place for precise stance adjustment.

FEATURES

Aluminum Disks: Oversize aluminum center disk overlaps binding channels for maximum strength and rigidity.

3° Canting: With 3° of canting to reduce strain, your knees will thank you.

Oversize Disk: Center disk overlaps binding channels for maximum strength and rigidity.

Adjustability: near infinite adjustability, for your perfect stance placement.

+/- 1/4 inch (6.5mm) of toe/heel adjustment in .5 inch (1.3mm) increments.

+/- 30° angle adjustments in 3° increments.

Stance width adjustments: .17 inch (4.2mm) increments.

Superior Materials: Bindings slide on soft nylon for effortless installation.

Compatible with all splitboards using the industry standard splitboard insert pattern.
For use with all puck compatible splitboard bindings (with the exception of the K2 Kwicker)

Not Compatible with Burton channel style splitboards or DIY splitboards (without the industry standard splitboard insert pattern).